Rheem Select 2.5 Ton 14.3 SEER2 Heat Pump Condenser

WP14AY30AJ2NA Rheem Select 2.5 Ton Heat Pump

WP14AY30AJ2NA is a Rheem Select outdoor heat pump condenser designed to provide dependable heating and cooling for compatible residential split systems. Its nominal 2.5 ton capacity makes it suitable for homes requiring balanced year-round comfort, subject to a professional HVAC load calculation. This model combines two-stage operation, durable construction and modern R-454B refrigerant technology.

Unlike a straight-cool air conditioner, this heat pump can reverse the refrigeration cycle. During warm weather, it removes heat from the indoor space and transfers it outdoors. During cooler weather, it collects available outdoor heat and transfers it inside. This allows one properly matched system to provide both cooling and heating.

Efficient Two-Stage Operation

The WP14AY30AJ2NA uses a two-stage scroll compressor with low and high operating capacities. During periods of moderate demand, the lower stage can help maintain consistent indoor temperatures, support humidity control and reduce unnecessary system cycling. The higher stage supplies additional heating or cooling capacity when outdoor conditions become more demanding.

Two-stage operation can provide more precise comfort than standard single-stage equipment. Actual operation and performance depend on the compatible indoor unit, thermostat configuration, airflow settings and professional system commissioning.

2.5 Ton Heating and Cooling Capacity

The WP14AY30AJ2NA carries a nominal capacity designation of 30,000 BTU per hour. With Rheem’s published H2TY3617STANN air-handler combination, it provides approximately 28,600 BTU per hour of total cooling capacity and approximately 950 CFM of indoor airflow under specified rating conditions.

Rheem lists approximately 28,000 BTU per hour of heating capacity at 47°F and 16,000 BTU per hour at 17°F with that equipment combination. Actual performance varies according to outdoor temperature, indoor airflow, ductwork, equipment selection and installation conditions.

Equipment tonnage should not be selected using square footage alone. Climate, insulation, windows, ceiling height, occupancy, air leakage and duct condition all influence the heating and cooling load. A qualified HVAC professional should complete a Manual J load calculation before purchase.

14.3 SEER2 Matched-System Efficiency

The WP14AY30AJ2NA achieves 14.3 SEER2, 9.0 EER2 and 7.5 HSPF2 with Rheem’s specified indoor equipment match. These ratings apply to the complete certified system rather than the outdoor condenser operating independently.

The final efficiency depends on the exact air handler, metering device, thermostat, blower configuration and AHRI-rated combination. Refrigerant charging, indoor airflow, duct design and equipment commissioning also affect comfort and real-world performance.

Modern R-454B Refrigerant

The WP14AY30AJ2NA uses R-454B, a lower-global-warming-potential refrigerant found in newer residential HVAC equipment. All connected indoor components must be approved for R-454B operation.

Because R-454B is classified as an A2L refrigerant, installation and service require compatible tools, approved components and appropriate safety procedures. Rheem lists approximately 99 ounces of factory-supplied refrigerant for this model.

The final refrigerant charge depends on the installed line-set length and manufacturer instructions. A qualified technician must complete pressure testing, evacuation, charging and system commissioning. Rheem’s required refrigerant detection and mitigation components must also be installed correctly.

Durable Outdoor Construction

A fully louvered steel cabinet helps protect the outdoor coil from weather exposure and common yard hazards. Rheem’s optimized condenser-coil design supports efficient airflow and heat transfer. The expanded service-valve area gives technicians additional working space during installation and maintenance.

The WP14AY30AJ2NA has a listed sound level of approximately 72 dB and an operating weight of approximately 178 pounds. Its outdoor fan moves approximately 3,391 CFM under published operating conditions.

The cabinet measures approximately 27.17 inches high, 33.66 inches wide and 33.66 inches deep. A stable, level condenser pad and the manufacturer’s required airflow and service clearances must be provided at the installation location.

Electrical and Line-Set Requirements

This condenser operates on a 208/230-volt, single-phase, 60 Hz electrical supply. Rheem lists a minimum circuit ampacity of 20 amps and maximum overcurrent protection of 30 amps. Final wiring, breaker and disconnect requirements must follow the unit nameplate, installation manual and applicable electrical codes.

The published refrigerant connections are 3/8 inch for the liquid line and 3/4 inch for the suction line. An existing line set should not be reused until its size, condition, length, cleanliness and compatibility with R-454B equipment have been professionally verified.

Matching Indoor Equipment Required

The WP14AY30AJ2NA is the outdoor heat pump condenser only. It does not include an indoor air handler, electric heat kit, thermostat, refrigerant line set, condenser pad or installation materials unless those items are specifically included in the selected package.

A compatible R-454B air handler and approved metering device are required to create a complete system. An optional electric heat kit may supply supplemental or emergency heating during colder conditions. The correct heat-kit capacity depends on the property’s heating load, electrical service and air-handler model.

Professional Installation Required

The WP14AY30AJ2NA should be installed by a qualified HVAC professional trained to work with R-454B equipment. Proper airflow, pressure testing, evacuation, refrigerant charging, wiring, drainage and system commissioning are essential for safe and dependable performance.

Review the official Rheem product specifications and browse our replacement condensers and heat pumps before ordering. Confirm the model number, voltage, refrigerant and approved indoor equipment match with your installer.