Rheem Select 2 Ton Heat Pump System – Multiposition – 14.3 SEER2

The Rheem Select 2 Ton Heat Pump System is a complete residential heating and cooling configuration designed for properties that use an air handler and electric heat instead of a gas furnace. It combines a two-stage outdoor heat pump, a multiposition indoor air handler, and a 10 kW-class auxiliary electric heat kit.

This matched system has a nominal equipment capacity of 24,000 BTU and an AHRI-certified cooling capacity of 22,800 BTU. The documented combination is rated at 14.3 SEER2, 9.0 EER2, and 7.5 HSPF2 under AHRI reference number 217047499. Actual performance depends on correct sizing, installation quality, airflow, ductwork, climate, and building conditions.

Rheem Select 2 Ton Heat Pump System Overview

The WP14AY24AJ2NA outdoor unit is part of the Rheem Endeavor® Line Select™ Series. Unlike a straight-cool air conditioner, this heat pump can reverse the refrigeration cycle to provide both cooling and primary electric heating.

Its two-stage scroll compressor operates at different capacity levels to support more consistent indoor temperatures and improved humidity management compared with conventional single-stage operation under appropriate conditions.

The outdoor heat pump is matched with the WH2TY2417STANNJ air handler. This indoor unit features a constant-torque blower motor, two-stage airflow operation, an aluminum N-coil, and a factory-installed thermostatic expansion valve.

The air handler’s multiposition cabinet supports upflow, downflow, horizontal-left, and horizontal-right applications when installed according to current Rheem instructions and applicable building codes.

What’s Included

• Outdoor heat pump: Rheem Select WP14AY24AJ2NA
• Indoor air handler: Rheem Select WH2TY2417STANNJ
• Electric heat kit: Rheem RXBH-1724A10J-B
• Matched-system reference: AHRI 217047499

The thermostat, refrigerant line set, equipment pad, electrical disconnects, breakers, wiring, drain components, installation materials, and other accessories should be confirmed separately unless they are specifically listed as included with the order.

Key Features

• Two-stage heat pump operation for residential cooling and heating
• Nominal 2-ton or 24,000 BTU equipment class
• AHRI-certified cooling capacity of 22,800 BTU
• 14.3 SEER2, 9.0 EER2, and 7.5 HSPF2 matched-system ratings
• R-454B low-GWP refrigerant platform
• Constant-torque indoor blower motor
• Two-stage indoor airflow operation
• Factory-installed thermostatic expansion valve
• Multiposition air-handler installation
• Auxiliary electric heat for supplemental and emergency heating

Technical Specifications

WP14AY24AJ2NA Outdoor Heat Pump

• Product line: Rheem Endeavor® Line Select™ Series
• System type: Split-system heat pump
• Nominal capacity: 24,000 BTU / 2 tons
• Certified cooling capacity: 22,800 BTU
• Compressor: Two-stage scroll compressor
• Refrigerant: R-454B
• Electrical supply: 208/230 volts, single phase, 60 Hz
• Minimum circuit ampacity: 16 amps
• Maximum overcurrent protection: 25 amps
• Sound level: 73 dB
• Dimensions: Approximately 25.16 inches high × 29.53 inches wide × 29.53 inches deep

WH2TY2417STANNJ Indoor Air Handler

• Nominal capacity: 24,000 BTU / 2 tons
• Cabinet width: 17.5 inches
• Cabinet height: Approximately 42.5 inches
• Cabinet depth: Approximately 21.69 inches
• Electrical supply: 208/240 volts, single phase, 60 Hz
• Motor type: Constant-torque blower motor
• Airflow operation: Two stage
• Coil configuration: Aluminum N-coil
• Metering device: Factory-installed TXV
• Installation positions: Upflow, downflow, horizontal left, and horizontal right

RXBH-1724A10J-B Electric Heat Kit

• Heat-kit class: 10 kW
• Heating output: 7.2 kW at 208 volts or 9.6 kW at 240 volts
• Electrical supply: 208/240 volts, single phase
• Application: Auxiliary and emergency electric heating

System Compatibility

The efficiency ratings for this Rheem Select 2 Ton Heat Pump System apply to the documented combination of WP14AY24AJ2NA and WH2TY2417STANNJ under AHRI reference number 217047499. Substituting a different outdoor unit, air handler, coil, metering device, or blower configuration can change capacity and efficiency.

The thermostat must support the required heat-pump stages, auxiliary electric heat, and emergency-heat operation. The installing contractor must verify the available electrical service, breaker capacity, conductor sizing, disconnects, line-set requirements, condensate drainage, equipment clearances, and duct-system airflow.

Choosing the Rheem Select 2 Ton Heat Pump System

The Rheem Select 2 Ton Heat Pump System is intended for residential applications requiring electric cooling and heating without a gas furnace. Before ordering, compare this configuration with other heat pump systems available from Xpress AC Supply.

Correct sizing is essential when selecting a Rheem Select 2 Ton Heat Pump System. A qualified HVAC contractor should complete a load calculation and verify the ductwork, electrical service, installation position, thermostat requirements, and local climate conditions.

When properly matched and installed, the Rheem Select 2 Ton Heat Pump System provides two-stage heat-pump operation with auxiliary electric heat for year-round residential comfort.

R-454B Refrigerant Information

This equipment is engineered for R-454B refrigerant. R-454B is classified as an A2L refrigerant and requires compatible installation tools, components, handling procedures, and safety practices.

R-454B must not be mixed with R-410A or used with components that have not been approved for the applicable refrigerant and system configuration. Refrigerant lines and accessories must be evaluated for compatibility before installation.

The air handler incorporates equipment intended for the R-454B platform, including refrigerant detection and mitigation provisions. Installation, commissioning, evacuation, charging, leak testing, and service must be completed by qualified HVAC personnel following current Rheem instructions and applicable codes.

Warranty and Documentation

Rheem lists limited and conditional warranty coverage for eligible equipment. Available coverage and registration requirements can vary by component, installation, application, purchaser, and location. Product registration may be required within the specified period to receive conditional coverage.

Review the current warranty certificate before purchase and register eligible equipment directly through Rheem after installation. Model numbers, serial numbers, proof of purchase, installation information, and homeowner information may be required.

For verified product information, review the official Rheem WP14AY24AJ2NA specifications and the Rheem warranty and product registration portal.

Professional Installation Notice

The Rheem Select 2 Ton Heat Pump System must be sized and installed by qualified HVAC professionals. Tonnage alone does not determine whether this system is appropriate for a particular property.

A room-by-room load calculation should consider climate, insulation, windows, air leakage, occupancy, construction, ductwork, and indoor design temperatures. Selecting equipment based only on square footage can result in incorrect sizing.

Professional installation is also necessary to establish correct airflow, refrigerant charge, electrical protection, thermostat configuration, condensate drainage, and auxiliary-heat operation. Improper sizing or installation can reduce efficiency, comfort, reliability, and equipment life while potentially affecting warranty eligibility.