Rheem Select 2 Ton Electric HVAC System with Heat Kit – Up to 15.2 SEER2

The Rheem Select 2 Ton Electric System is a complete residential straight-cool package combining an R-454B air conditioner, a multiposition air handler and a 10 kW electric heat kit. This equipment combination provides dependable cooling, supplemental electric heating and flexible indoor-unit installation for residential replacement and new-construction applications.

Rheem Select 2 Ton Electric System Overview

The Rheem Select 2 Ton Electric System combines equipment from the Rheem Endeavor® Line Select™ Series. Its WA14AY outdoor air conditioner provides a nominal cooling capacity of approximately 24,000 BTU and uses single-stage operation for consistent residential cooling.

The WA14AY product line offers cooling efficiencies of up to 15.2 SEER2. The exact efficiency of an installed system depends on the specific outdoor and indoor equipment combination, AHRI certification, airflow settings, ductwork and installation conditions. Buyers should verify the applicable AHRI certificate when a specific efficiency rating is required.

What Is Included

This complete electric HVAC package includes the following components:

• Rheem WA14AY24AJ1NA air conditioner: Two-ton outdoor condenser using R-454B refrigerant, single-stage operation and the Rheem Endeavor Line Select design.
• Rheem WH2TY2417STANNJ air handler: Multiposition indoor air handler with approximately 24,000 BTU nominal capacity, a constant-torque motor, two-stage airflow and factory-installed TXV.
• PROTECH RXBH-1724A10J-B electric heat kit: 10 kW auxiliary electric heater designed for 208–240-volt, single-phase service and equipped with circuit breakers and Smart Plug compatibility.

Every component in this Rheem Select 2 Ton Electric System must be properly matched, installed and configured by a qualified HVAC professional. Additional installation materials may be required, including a thermostat, condenser pad, refrigerant line set, disconnect, electrical wiring, drain components and duct transitions.

Key Features of the Rheem Select 2 Ton Electric System

• Nominal two-ton cooling capacity
• Cooling efficiency of up to 15.2 SEER2
• R-454B low-GWP refrigerant
• Single-stage outdoor air conditioner
• Constant-torque indoor blower motor
• Two-stage airflow capability
• Factory-installed thermal expansion valve
• Four-way convertible air-handler design
• 10 kW electric heat kit with circuit breakers
• Residential straight-cool configuration

WH2TY Multiposition Air Handler

The included WH2TY2417STANNJ air handler features a 17.5-inch-wide cabinet and a versatile four-way convertible design. It can accommodate upflow, downflow, horizontal-left and horizontal-right applications when installed according to Rheem requirements and applicable building codes.

Its aluminum indoor coil is designed for durability and corrosion resistance. The insulated cabinet supports quieter operation, while the constant-torque motor and two-stage airflow help the installer configure appropriate indoor airflow for the matched system.

10 kW Electric Heat Kit

The PROTECH RXBH-1724A10J-B adds electric resistance heating to the air handler. This allows the system to provide indoor heating without a gas furnace. The heat kit requires suitable electrical service, wiring and overcurrent protection. A qualified professional must confirm the property’s available electrical capacity before installation.

Sizing and Residential Application

A Rheem Select 2 Ton Electric System may be suitable for a smaller residential property, apartment, addition or individual conditioned area. However, HVAC capacity should never be selected using square footage alone. Climate, insulation, ceiling height, windows, occupancy, orientation, ductwork and air leakage all influence the required capacity.

A licensed HVAC professional should perform a Manual J load calculation before purchase. The installer should also verify duct capacity, electrical service, airflow, refrigerant-line requirements and equipment compatibility. Incorrect sizing can produce poor humidity control, uneven temperatures, higher energy use and shortened equipment life.

R-454B Refrigerant Compatibility

The outdoor air conditioner and indoor air handler are designed for R-454B refrigerant. Existing indoor equipment, refrigerant components, tools and installation procedures must be compatible with this refrigerant. R-454B systems require professional handling and installation according to manufacturer instructions and applicable safety standards.

Review the official Rheem WA14AY product information for current manufacturer specifications, features and available technical documentation.

Professional Installation and Warranty

The Rheem Select 2 Ton Electric System must be installed by a qualified HVAC professional in accordance with manufacturer requirements and local codes. Warranty eligibility, duration and coverage depend on the individual components, installation and product-registration requirements. Review all warranty documents and complete any required registration after installation.

Need additional materials? Browse our electric HVAC system kits or contact Xpress AC Supply before ordering to confirm equipment compatibility.