AMHE3D10B2N1 – 3 Ton Manufactured Housing Electric Furnace

The AMHE3D10B2N1 is a 3 ton ADP mFurnace™ manufactured home electric furnace. It combines a five-speed ECM blower with factory-installed 10 kW electric heat, circuit-breaker line-voltage connection, and 208/240-volt single-phase operation. The unit is factory configured for downflow airflow and can be converted in the field for an approved upflow installation.

This furnace is designed for manufactured housing HVAC applications and can be paired with compatible air-conditioning or heat pump equipment. The evaporator coil, outdoor unit, coil cabinet, thermostat, refrigerant components, and installation materials are not included unless they are specifically listed with the product configuration.

AMHE3D10B2N1 Product Overview

The AMHE3D10B2N1 belongs to the ADP Manufactured Home Electric Furnace series. Its standard mobile home footprint and two-piece installation concept allow the furnace to work with compatible ADP M Series evaporator coils and appropriately sized coil cabinets.

The 3 ton designation identifies the furnace blower size rather than the electric heating output. ADP publishes a nominal airflow range of 900 to 1,100 CFM for the AMHE3D furnace platform. Final airflow must be configured according to the matched outdoor equipment, evaporator coil, duct system, electric heat requirements, and installation instructions.

What’s Included

• AMHE3D10B2N1 manufactured home electric furnace
• Five-speed high-efficiency ECM blower motor
• Factory-installed 10 kW electric heating assembly
• Factory-installed circuit-breaker connection
• Integrated 40 VA Class 2 transformer
• Blower-door safety switch
• Low-voltage thermostat terminal board
• Factory-installed internal controls and wiring

A compatible evaporator coil and coil cabinet are required for a complete cooling or heat pump installation. Verify every included component before ordering a complete system.

Key Features

• Manufactured housing design: Standard footprint developed for compatible mobile home installations.
• Five-speed ECM motor: Provides selectable airflow settings for properly matched heating and cooling equipment.
• 10 kW electric heat: Factory-installed resistance heat with a published nominal output of approximately 34,121 BTU per hour at 240 volts.
• Downflow configuration: Factory configured for downflow and field convertible to an approved upflow arrangement.
• Circuit-breaker connection: The letter B in the model identifies the line-voltage circuit-breaker configuration.
• Service accessibility: Slide-out blower assembly and removable blower panel support professional inspection and service.
• Safety switch: The blower-door switch disconnects operation when the access door is removed.
• Insulated cabinet: The furnace cabinet and door use foil-faced insulation to help manage operating sound.

AMHE3D10B2N1 Technical Specifications

• Manufacturer: Advanced Distributor Products (ADP)
• Product line: mFurnace™
• Model: AMHE3D10B2N1
• Equipment type: Manufactured home electric furnace
• Blower size: 3 tons
• Published nominal airflow range: 900–1,100 CFM
• Blower motor: Five-speed ECM
• Motor horsepower: 1/2 HP
• Electric heat: 10 kW factory installed
• Nominal heating capacity at 240 volts: Approximately 34,121 BTU per hour
• Line-voltage connection: Circuit breaker
• Supply voltage: 208/240 volts
• Frequency: 60 Hz
• Phase: Single phase
• Factory airflow configuration: Downflow
• Convertible configuration: Upflow when installed according to ADP instructions
• Furnace height: 33 inches
• Furnace width: 19.8 inches
• Furnace depth: 23.4 inches
• Approximate published packaged weight: 85 pounds
• Coil cabinet: Not included

Electrical Requirements

The AMHE3D10B2N1 requires a 208/240-volt, 60 Hz, single-phase electrical supply. ADP’s published electrical data for the 3 ton, 10 kW configuration lists one electrical circuit. The minimum circuit ampacity is 50 amps at 208 volts and 57 amps at 240 volts. The published maximum circuit-breaker size is 50 amps at 208 volts and 60 amps at 240 volts.

Electrical requirements must be confirmed using the furnace nameplate and current installation instructions. The installing professional is responsible for conductor sizing, overcurrent protection, grounding, disconnecting means, and compliance with applicable electrical and manufactured housing codes.

System Compatibility

The AMHE3D10B2N1 can be used with compatible split-system air conditioners or heat pumps. ADP identifies the mFurnace platform as compatible with properly matched 2 to 5 ton systems; however, this specific model has a 3 ton blower size and must be evaluated using its published airflow capabilities.

Do not match the furnace to an outdoor unit based only on nominal tonnage. The evaporator coil, outdoor equipment, refrigerant, airflow, ductwork, electrical service, coil cabinet, and AHRI-rated combination must all be verified.

Browse compatible mobile home HVAC systems or view additional HVAC furnaces.

Coil Cabinet and Installation Configuration

The furnace does not include a coil cabinet. Select the cabinet according to the evaporator coil’s physical dimensions, required airflow orientation, filter arrangement, and ADP compatibility information. The AMHE3D10B2N1 is shipped for downflow operation and may be converted to upflow only by following the manufacturer’s approved procedure.

The furnace cabinet measures approximately 33 inches high, 19.8 inches wide, and 23.4 inches deep. These are equipment dimensions and should not be confused with shipping-box dimensions.

Efficiency and System Ratings

This electric furnace does not receive an independent SEER2, EER2, or HSPF2 rating. Those efficiency values apply to a complete matched air-conditioning or heat pump system. Verify the outdoor unit, evaporator coil, furnace blower, and AHRI certificate before assigning an efficiency rating to the complete system.

Warranty and Official Documentation

ADP lists a five-year limited warranty and an available ten-year extended limited warranty for eligible registered equipment. Registration and coverage depend on the installation date, location, product eligibility, and current warranty conditions. ADP generally requires registration within 90 days of installation, subject to jurisdiction-specific protections. :contentReference[oaicite:1]{index=1}

• ADP mFurnace product information
• ADP mFurnace specification guide
• ADP warranty information and registration

Professional Installation Notice

The AMHE3D10B2N1 requires professional installation. A qualified HVAC and electrical professional must verify the equipment match, airflow setting, electrical circuit, overcurrent protection, thermostat wiring, duct connections, furnace orientation, coil cabinet, and compliance with manufacturer instructions and applicable codes.