AMHE5D15B2N1 – 5 Ton MH Electric Furnace / Mobile Home

The AMHE5D15B2N1 is a 5 ton ADP mFurnace™ manufactured home electric furnace. It combines a five-speed ECM blower with factory-installed 15 kW electric resistance heat, circuit-breaker line-voltage connections, and 208/240-volt single-phase operation. The unit is factory configured for downflow airflow and can be converted in the field for an approved upflow installation.

This furnace is designed for manufactured housing HVAC applications and can support compatible air-conditioning or heat pump systems. The evaporator coil, outdoor unit, coil cabinet, thermostat, refrigerant components, and installation materials are not included unless they are specifically listed in the product configuration.

AMHE5D15B2N1 Product Overview

The AMHE5D15B2N1 belongs to the ADP Manufactured Home Electric Furnace series. Its standard mobile home footprint and two-piece installation design allow the furnace to be combined with compatible ADP M Series evaporator coils and correctly sized coil cabinets.

The 5 ton designation identifies the blower size rather than the electric heating output. ADP publishes a nominal airflow range of 1,200 to 1,800 CFM for the AMHE5D furnace platform. Final airflow must be selected according to the outdoor equipment, evaporator coil, duct system, static pressure, heating requirements, and manufacturer instructions.

What’s Included

• AMHE5D15B2N1 manufactured home electric furnace
• Five-speed high-efficiency ECM blower motor
• Factory-installed 15 kW electric heating assembly
• Factory-installed circuit-breaker connections
• Integrated 40 VA Class 2 transformer
• Blower-door safety switch
• Low-voltage thermostat terminal board
• Factory-installed internal controls and wiring

A compatible evaporator coil and coil cabinet are required for a complete air-conditioning or heat pump installation. Review the final product configuration to confirm every included component before ordering.

Key Features

• Manufactured housing design: Standard footprint developed for compatible mobile home installations.
• Five-speed ECM motor: Provides selectable airflow settings for properly matched heating and cooling equipment.
• 15 kW electric heat: Factory-installed resistance heating with a nominal published capacity of approximately 51,180 BTU per hour at 240 volts.
• Downflow configuration: Factory configured for downflow operation and field convertible to an approved upflow arrangement.
• Circuit-breaker connections: The letter B in the model number identifies the circuit-breaker line-voltage configuration.
• Service accessibility: Slide-out blower assembly and accessible blower panel simplify professional inspection and maintenance.
• Door safety switch: Interrupts operation when the blower access door is removed.
• Insulated construction: The galvanized-steel cabinet and door include foil-faced insulation.
• Built-in fan delay: ADP specifies a one-second fan-on delay and a 45-second fan-off delay.

AMHE5D15B2N1 Technical Specifications

• Manufacturer: Advanced Distributor Products (ADP)
• Product line: mFurnace™
• Model: AMHE5D15B2N1
• Equipment type: Manufactured home electric furnace
• Blower size: 5 tons
• Published nominal airflow range: 1,200–1,800 CFM
• Blower motor: Five-speed ECM
• Motor horsepower: 3/4 HP
• Blower motor full-load amps at 240 volts: 5.8 amps
• Blower wheel: 11 × 9 inches
• Electric heat: 15 kW factory installed
• Nominal heating capacity at 240 volts: Approximately 51,180 BTU per hour
• Line-voltage connection: Circuit breakers
• Supply voltage: 208/240 volts
• Frequency: 60 Hz
• Phase: Single phase
• Factory airflow configuration: Downflow
• Convertible configuration: Upflow when installed according to ADP instructions
• Furnace height: 33 inches
• Furnace width: 19.8 inches
• Furnace depth: 23.4 inches
• Approximate published packaged weight: 100 pounds
• Coil cabinet: Not included

Electrical Requirements

The AMHE5D15B2N1 requires a 208/240-volt, 60 Hz, single-phase electrical supply. The 15 kW configuration uses two electrical circuits. ADP divides the heating load into a 10 kW circuit and a 5 kW circuit.

• First circuit minimum ampacity: 52.6 amps at 208 volts or 59.3 amps at 240 volts
• First circuit maximum breaker: 60 amps at 208 or 240 volts
• Second circuit minimum ampacity: 22.6 amps at 208 volts or 26 amps at 240 volts
• Second circuit maximum breaker: 25 amps at 208 volts or 30 amps at 240 volts

These published values must be checked against the furnace nameplate and current installation instructions. The installing professional is responsible for conductor sizing, breaker selection, grounding, disconnecting means, and compliance with applicable electrical and manufactured housing codes.

System Compatibility

The AMHE5D15B2N1 is intended for use with compatible split-system air conditioners or heat pumps. ADP identifies its mFurnace family as compatible with properly matched 2 to 5 ton systems; however, this particular model uses the 5 ton blower platform.

Do not select the furnace or outdoor unit based only on nominal tonnage. The evaporator coil, outdoor equipment, refrigerant, blower airflow, ductwork, electrical service, coil cabinet, and AHRI-certified combination must all be verified before installation.

Browse compatible mobile home HVAC systems or view additional HVAC furnaces.

Coil Cabinet and Installation Configuration

The furnace does not include a coil cabinet. Select the cabinet according to the evaporator coil’s physical dimensions, required airflow orientation, filter arrangement, and ADP compatibility information.

The AMHE5D15B2N1 is shipped for downflow operation and may be converted to upflow only by following the manufacturer’s approved procedure. The furnace measures approximately 33 inches high, 19.8 inches wide, and 23.4 inches deep. These are equipment dimensions and should not be confused with shipping-box dimensions.

Efficiency and System Ratings

This electric furnace does not have an independent SEER2, EER2, or HSPF2 rating. These ratings apply to a complete matched air-conditioning or heat pump system. Verify the outdoor unit, evaporator coil, furnace blower, and AHRI certificate before assigning an efficiency rating to the complete system.

Warranty and Official Documentation

ADP lists a five-year limited warranty and an available ten-year extended limited warranty for eligible registered equipment. Registration, coverage, and duration depend on the installation date, location, model eligibility, and current warranty conditions. Registration is generally required within 90 days of installation, subject to jurisdiction-specific protections.

• ADP mFurnace product information
• ADP mFurnace specification guide
• ADP warranty information and registration

Professional Installation Notice

The AMHE5D15B2N1 requires professional installation. A qualified HVAC and electrical professional must verify the equipment match, blower setting, electrical circuits, overcurrent protection, thermostat wiring, duct connections, furnace orientation, coil cabinet, and compliance with manufacturer instructions and applicable codes.