Rheem Select 4 Ton Mobile Home Heat Pump System – 14.8 SEER2

Rheem Select 4 Ton Mobile Home Heat Pump System Overview

The Rheem Select 4 Ton Mobile Home Heat Pump System is a complete heating and cooling configuration for compatible manufactured homes with central ductwork. It combines a Rheem Select two-stage outdoor heat pump, a manufactured housing evaporator coil, a downflow electric furnace, and a matching louvered coil cabinet.

This matched configuration is rated at 14.8 SEER2 under AHRI reference number 218325247. The outdoor heat pump provides 48,000 BTU of nominal capacity and uses R-454B refrigerant.

The heat pump provides both cooling and heat-pump heating. The included electric furnace circulates conditioned air through the home and supplies 15 kW of supplemental electric resistance heat when properly installed and configured by a qualified HVAC professional.

What’s Included

• WP14AY48AJ2NA: Rheem Endeavor Line Select Series 4-ton, two-stage heat pump
• M48E36AR: 4-ton manufactured housing uncased evaporator coil
• AMHE5D15B2N1: 5-ton downflow manufactured housing electric furnace with 15 kW electric heat
• MHCDLS30: Downflow louvered coil cabinet with solid top

Each component of the Rheem Select 4 Ton Mobile Home Heat Pump System performs a specific function. The outdoor heat pump transfers heat for cooling and heating, the indoor coil supports refrigerant heat exchange, the electric furnace circulates conditioned air and supplies supplemental heat, and the cabinet supports the required downflow arrangement.

Key Features

• Nominal 4-ton outdoor capacity
• AHRI-certified 14.8 SEER2 matched-system performance
• Two-stage scroll compressor
• R-454B refrigerant
• 208/230V, single-phase outdoor electrical configuration
• Downflow manufactured housing application
• Five-speed ECM indoor blower motor
• 15 kW supplemental electric resistance heat
• Factory-installed circuit breaker in the electric furnace
• Copper-slab indoor evaporator coil
• Non-bleed heat-pump and air-conditioning TXV
• Refrigerant Detection System controller and sensor

Technical Specifications

Outdoor Heat Pump: WP14AY48AJ2NA

• Brand and series: Rheem Endeavor Line Select Series
• System type: Split-system heat pump
• Nominal capacity: 4 tons
• Nominal cooling capacity: 48,000 BTU
• Compressor: Two-stage scroll compressor
• Refrigerant: R-454B
• Voltage: 208/230V
• Phase: Single phase
• Frequency: 60 Hz
• Minimum circuit ampacity: 27 amps
• Maximum overcurrent protection: 45 amps
• Factory refrigerant charge: 115 ounces
• Liquid-line connection: 3/8 inch
• Suction-line connection: 7/8 inch
• Sound level: Approximately 74 dB
• Outdoor unit dimensions: Approximately 35.17 inches high, 33.66 inches wide, and 33.66 inches deep
• Unit weight: Approximately 253 pounds

Manufactured Housing Coil: M48E36AR

• Nominal coil capacity: 4 tons
• Application: Manufactured housing
• Configuration: Uncased evaporator coil
• Coil construction: Copper slab
• Refrigerant compatibility: R-454B
• Metering device: Non-bleed heat-pump and air-conditioning TXV
• Safety components: Refrigerant Detection System controller and sensor

Electric Furnace: AMHE5D15B2N1

• Application: Manufactured housing
• Airflow configuration: Downflow
• Nominal airflow size: 5 tons
• Blower motor: Five-speed ECM motor
• Electric heat capacity: 15 kW
• Electrical supply: 208–240V, single phase, 60 Hz
• Overcurrent protection: Circuit breaker

Coil Cabinet: MHCDLS30

• Installation configuration: Downflow
• Door: Louvered
• Top: Solid
• Cabinet height: 30.50 inches

System Compatibility

The Rheem Select 4 Ton Mobile Home Heat Pump System is intended for compatible manufactured housing installations requiring downflow airflow. The 5-ton furnace designation represents its available indoor airflow range and does not change the system’s 4-ton outdoor cooling capacity.

Before ordering, a qualified HVAC professional must verify compatibility with the home’s ductwork, electrical service, refrigerant piping, thermostat controls, condensate drainage, installation clearances, structural supports, and applicable manufactured housing requirements.

R-454B Refrigerant Information

The WP14AY48AJ2NA heat pump and M48E36AR indoor coil are designed for R-454B refrigerant. R-454B is classified as an A2L refrigerant and requires approved components, tools, installation procedures, and safety practices.

The included indoor coil incorporates a Refrigerant Detection System controller and sensor. Installation and commissioning of the Rheem Select 4 Ton Mobile Home Heat Pump System must follow Rheem instructions, applicable codes, and current A2L refrigerant requirements.

Efficiency and System Sizing

This matched combination is listed at 14.8 SEER2 under AHRI reference number 218325247. The complete matched-system rating should be used instead of applying the outdoor unit’s family efficiency claims to every possible equipment combination.

Actual comfort and energy consumption depend on climate, installation quality, thermostat settings, insulation, duct condition, maintenance, and the building’s heating and cooling load.

A professional Manual J load calculation should be completed before purchasing the Rheem Select 4 Ton Mobile Home Heat Pump System. Square footage alone cannot determine the appropriate equipment capacity because homes of similar size may have different insulation, windows, occupancy, ductwork, orientation, and climate conditions.

Warranty and Official Documentation

Manufacturer warranty coverage varies according to the component, application, registration status, and installation conditions. Rheem lists five-year limited parts coverage and conditional ten-year compressor coverage for the WP14AY heat pump when applicable registration and eligibility requirements are satisfied. Separate terms may apply to the indoor coil, furnace, and cabinet.

Review the documentation supplied with every component and visit the official Rheem warranty and registration portal to confirm registration deadlines, exclusions, eligibility, and available coverage for the installed equipment.

Professional Installation Notice

The Rheem Select 4 Ton Mobile Home Heat Pump System requires professional installation. A qualified HVAC technician must confirm equipment matching, system sizing, airflow, ductwork, electrical circuits, refrigerant piping, controls, clearances, condensate drainage, and compliance with local and manufactured housing codes.

Improper sizing, refrigerant charging, wiring, airflow setup, or installation can reduce performance and may affect equipment safety and warranty eligibility. Xpress Supply sells HVAC equipment but does not perform installation services.

Explore other available configurations in the mobile home HVAC systems category.